Top 10 Best 36 v 800w brushed speedcontroler throttle twish grip for scooter Reviews

This article may contain affiliate links. When you purchase through links on our site, we may earn an affiliate commission.

Top 10 Rated 36 v 800w brushed speedcontroler throttle twish grip for scooter in 2021 Comparison Table

Are you searching for top 10 rated 36 v 800w brushed speedcontroler throttle twish grip for scooter for your money in 2021? After evaluating and analyzing in detail more than 92,297 customer satisfaction about top 10 best 36 v 800w brushed speedcontroler throttle twish grip for scooter in 2021, we have come up with the top 10 rated products you may be interested in. We have ranked the best brands from Artificial Intelligent and Big Data, as you see below:

Our Best Choice: 24V Control Module, 7 Connectors, 4-Wire Throttle, Fits for Razor E100(V10+), E125 (V10+), E150 (All Version), eSpark(All Version), Trikke E2 (All Version), Model: ZK2400-DP-LD (ZK2400-DP-FS)


Our rating:4.3 out of 5 stars (4.3 / 5)





[ad_1]

Product Description

11

24V Control Module24V Control Module

Specification:

This 24V Control Module has 7 connectors (5 plastic connectors & 2 metal connectors). The throttle connection is 4 wire.Fits the following Razor models: E100(versions 10 and up), E125(versions 10 and up), E150(versions 1 and up), eSpark( all versions ), Trikke E2(versions 1 and up)Replace Razor Part #: W13111612015. Model No: ZK2400-DP-LD (ZK2400-DP-FS)

Note:

Please choose the right model according to your needs, because the inappropriate model can not be used.Razor E100 is different from Razor Power Core E100.

NOTE:

Most electric scooters and electric bikes have controllers which were made specifically for that model. Please carefully confirm the model number of controllers before buying.If a controller is available that will plug-and-play directly into an electric scooter or bike, however the controller is not listed by make and model, be careful when installing it because the wiring patterns going to the connectors may be different than that of the original controller. Double check the wiring to make sure that it is correct before installing the new controller. If the connectors are correct but the wiring going to the connectors are incorrect the pins can be removed and installed in different locations on the connector.Sometimes the brake switch becomes defective and locks into the on position which makes the controller turn off the motor. If the scooter works after disconnecting the brake switch then the brake switch is defective.

Controller Installation Tips:

1. Before replacing the controller make sure that the key switch or power switch is in the off position.

2. Disconnect the battery pack from the controller first when removing a controller, and connect the battery pack to the controller last when installing a controller.

3. Hang or block the rear wheel off the ground, or remove the chain or belt from the motor before connecting the battery pack to the controller. Sometimes due to damaged or incorrect wiring or faulty electrical components the rear wheel might spin uncontrollably when making the final wiring connection to the battery pack.

4. Do not short-circuit the battery terminals or wiring harness connector pins and make sure the batteries fit snug into place and that all of the wiring and connectors are in good serviceable condition.

24V Control Module24V Control Module

24V Control Module24V Control Module

24V Control Module24V Control Module

Model versions can be determined based on the 8-digit product ID code on your Razor product, can be found on the rectangular white sticker on the handlebar stem, side of the scooter deck, underneath the scooter, on the original battery charger, battery cover or on the bottom of the frame, on the cardboard box in which your scooter came. The last two digits are the version number (e.g. “01”=version 1, “02”=version 2, etc.)

IMPORTANT PRODUCT INSTALLATION INFORMATION:

The E100 / E125 Series Razor Scooters are a PUSH START Scooter. In order to engage the Motor, You need to push the Scooter, and twist the Throttle!

This 24 Volt Controller is Compatible ONLY with Razor E100 – E125 Versions 10 and up, E150 Version 1 and up, eSpark(All Versions),and Trikke E2 (All Versions).

Is Discontinued By Manufacturer‏:‎No
Package Dimensions‏:‎5.55 x 4.96 x 1.38 inches; 3.84 Ounces
Manufacturer recommended age‏:‎12 years and up
Date First Available‏:‎January 9, 2017
Manufacturer‏:‎QILI Power
ASIN‏:‎B07CN2G3R3

Replacement 24V controller with 4-wire throttle connector
COMPATIBLE ONLY WITH: Razor E100 & E125 Versions 10 and up, E150 All Versions, and eSpark(All Versions), Trikke E2 All Versions
Replace Razor part #: W13111612015, Model No: ZK2400-DP-LD (ZK2400-DP-FS)
The E100 series Razor scooter is a PUSH START scooter. You need to push the scooter, twist the throttle and then the motor will engage
Not Compatible With Powercore E100; 1-Year Warranty – Money-back satisfaction guarantee

We will be happy to hear your thoughts

      Leave a reply

      Safe Road