This article may contain affiliate links. When you purchase through links on our site, we may earn an affiliate commission.
Whether you drive a BMW M3 or something a little more modest, there is a good chance that you have experienced that sinking feeling when the engine refuses to kick over. And since you have landed here, there’s an even better chance that you’ve been through this recently.
So you think your car won’t start due to a clicking noise?
- Multiple clicks when trying to start your car
- Single click when trying to start your car
- Maintenance Matters
- Car Won’t Start Due To A Clicking Noise – Now You Know What to Do
Well, have no fear!
There are many possible reasons you may be hearing a clicking sound combined with no engine ignition.
Listen closely to exactly what is going on as you turn the ignition key. Do you hear multiple clicks or just the one? Are there any other sounds that may help you to diagnose what exactly is going on?
Therefore, I have decided to run through the most common causes of that dreadful clicking sound combined with no ignition.
Multiple clicks when trying to start your car
Ok, you turn the car key, and nothing happens except a repeated clicking sound. This is a common issue that’s usually easily fixed. What is most likely happening is that there is probably not enough juice in your battery to get the starter motor to engage. The rapid clicking you are hearing is the starter relay opening and closing repeatedly.
Battery Trouble Shooting
There could be a few issues here. If you have a multimeter, grab that bad boy and go check out what voltage your battery is currently sitting at.
A good battery should give you a reading of 12.65V. Anything below this number may indicate a deadening battery. A reading of less than 12.45V means it’s probably time for a new battery.
If you don’t have access to a multimeter, don’t stress. They’re easy enough to buy. Check out my reviews of the Best Automotive Multimeter and select the right one for you.
Another simple way to check the condition of your battery is by turning your key to the “on” position then turning on the headlights. If they are dim or off altogether, then your battery may need replacing.
Don’t rush out to buy a whole new battery just yet, though!
The very first thing you can do is to jump-start your car. To do this, simply grab some jumper cables and connect your car battery to another car’s battery. Make sure to connect the terminals correctly; positive to positive and negative to negative.
Stick shift vehicles…
If you own a stick shift vehicle, you can also try a rolling jump-start. All you need for this one is a slight incline or some strong and willing friends.
Put your car into second gear and turn the key to the on position. Push in the clutch and get the car rolling. You want it to be moving at no less than about three miles an hour. Then release the clutch. This should hopefully result in the engine kicking over.
Battery Cable Connections
Suppose you’re unable to jump-start your vehicle. Then the next step is to check out the battery cable connections. Have a look to make sure the connections haven’t come loose and see what sort of condition they are in. If they have loosened, then simply tighten them up and try to turn on your car again.
Corrosion on the connectors can also cause issues as it can impede voltage flow. If they do look corroded, then it’s time to grab your handy wire brush and some suitable thick gloves.
Next up, make a paste by mixing a small amount of water with some baking soda. Disconnect the battery (VERY IMPORTANT!), slather your baking soda paste all over the corrosion, and let it sit for a good 20 minutes.
Once that time is up, throw your gloves on and give it a good scrub with the wire brush. The corrosion should come away pretty quickly. Then all that’s left to do is reconnect the battery and try your car again. You can also use a product like these Best Battery Desulfators.
Are you in business yet?
If one of these suggested fixes works for you, that is excellent news! We recommend driving the car for at least 30 minutes to try to recharge the battery. After you have driven the car for half an hour or so, turn it off and leave it for the same amount of time, then go back and try to turn it on.
Did it work?
Yes? Awesome! You have most likely dodged a bullet, and your battery has recharged. But if your car fails to restart, then it’s time to buy a new battery. If so, check out my Best Car Battery reviews, the Best Battery for Diesel Truck, and Best Car Battery for Cold Weather.
But say you have done all these steps, and the issue still persists. Then it is most likely an alternator issue. The alternator recharges your car’s battery as you drive.
A faulty alternator is not the biggest issue and is a comparatively cheap fix, but you will need to take it into the shop unless you have a good home garage setup.
What costs to expect?
A reconditioned alternator will set you back about $450 for the parts and labor, with a new alternator going for a little more than double this price.
The last possible issue is parasitic drain. This drain could be caused by either an electrical device becoming faulty and remaining in the on position when it shouldn’t or from a short circuit. In this case, you’ll need to bring your car to an auto-electrician who will help diagnose and rectify any issues.
Single click when trying to start your car
If your Car Won’t Start Due To A Clicking Noise, but it’s only a single click you hear, this scenario is a little trickier to diagnose. However, we still suggest you run through the same first few steps that you would if you were hearing multiple clicks. So grab that multimeter and check for loose or corroded terminals. It could still be a quick and easy fix for you. If not, read on…
The most common cause of a single click is a failing starter relay, or possibly your whole starter has failed. If you hear a grinding or knocking sound with a single click, it is most probably one of these two issues. A new starter assembly with labor will set you back $300 to $600.
The absolute worst-case scenario is that you have a seized or locked-up engine. If you have failed to keep up to date with your oil changes and regular services, then this could be your issue, but cross your fingers it’s not!
What to do first?
In some cases, all that’s needed is for you to top up the engine oil, and the clicking sound and ignition issues will dissipate. If that doesn’t work, it’s time to call in a specialist.
An engine can also seize if it has been left to sit without any use for an extended period or through hydro and vapor locking. Freezing weather is a car’s worst enemy, so remember to top up your coolant before winter arrives to help combat this issue.
But if that’s what you’re dealing with…
There are some easy possible fixes to a frozen or seized engine.
If your engine has locked up, you can try to kick it over manually with a breaker bar and wrench, such as these Best Breaker Bars and Best Torque Wrenches. If it has frozen over, then turn the car on and let it sit, and warm up over a period of about 30 minutes.
As you can see, the best thing you can do to avoid these sorts of issues is regularly servicing and maintaining your car.
This need not break the bank. It’s just about having the right products, so check out my Best Oil Additives Reviews, the Best Oil Additives for Older Engines, what are the Best Oil Additives to Stop Leaks, and the Best Oil Additives for Noisy Lifters that you can buy in 2022.
Back to today’s discussion…
Car Won’t Start Due To A Clicking Noise – Now You Know What to Do
So as we can see, there are multiple issues that could cause your car to not turn over and to produce an audible clicking sound.
Hopefully, these troubleshooting points have helped, and you are back on the open road again soon. Remember, the most important thing for the health of your car is to keep it up to date with its services and to check the oil level and quality regularly.
Enjoy your vehicle and your rides.